Phone: +91-141-2460708 | Mobile: +91-9672861174 | Email: oswaltrfs@gmail.com
 

Manufacturing Process

The Technology for Manufacturing Oil-immersed Power & Distribution Transformers

Oswal Transformers thinking is driven by the commitment to quality. The complete in house manufacturing process helps us to ensure optimum quality of the transformer. We have complete testing facility to test and check all the major raw-materials used in manufacturing the transformer. CRGO laminations are cut and annealed in house to achieve minimum magnetic flux distortion. To ensure the best quality of the Coils of the transformer, winding wires and strips are also manufactured in house.

Fabrication section ensure the robustness, quality and fine finish of the tank and radiators of the transformer.

The manufacturing process of Transformer cover the following departments:-
  1. Coil Winding
  2. Core Assembly
  3. Core-Coil Assembly
  4. Tank-up
  5. Transformer Tank
  6. Painting & Finishing

Coil Winding

High Voltage Coils: H.V. Coils are the components of finished transformers. They are made on automatic layer setting winding machines. Coil Winding
  • A solid cylindrical former of predetermined diameter and length is being used as hase over which is made.
  • Generally round insulated wire of either copper (Cu) or Aluminium (Al) is used as basic raw material.
  • The coils are made in number of layers.
  • The starting and finishing leads of each coil are terminated on either side of the coil.
  • These leads are properly sleeved and locked at number of points.
Low Voltage Coils:
  • L.V. Coils are also one of the components of transformer. The procedure of making low voltage coil is generally same as described earlier.
  • The shape of the basic raw-material (Al or Cu) is rectangular.
The Test: The "Turn Test" is carried out on the H.V. Coils as per the specifications.

Core Assembly

  • The basic raw-material is COLD ROLLED GRAIN ORIENTED (CRGO) Silicon Steel
  • It is in the form of thin sheets & cut to size as per design.
  • Generally three different shapes of core laminations are used in one assembly.
  • Notching is performed to increase the magnetic path.
  • The laminations are put through annealing process.
  • These laminations are assembled in such a manner that there is no air gap between the joints of two consecutive sheets.
  • The entire assembly is done on a frame commonly known as core channel. These frames being used as a clamping support of the core assembly.

Core Coil Assembly

  • The components produced in the coil winding and core assembly stage are then taken into core-coil assembly stage.
  • The core assembly is vertically placed with the foot plate touching the ground. the top yoke of the core is removed. The limbs of the core are tightly wrapped with cotton tape and then varnished.
  • Cylinder made out of insulating press board/ pressphan paper is wrapped on all the three limbs.
  • Low Voltage Coil is placed on the insulated core limbs.
  • Insulating block of specified thickness and number are placed both at the top and bottom of the L.V.Coil.
  • Cylinder made out of corrugated paper or plain cylinder with oil ducts are provided over L.V.Coil.
  • H.V. Coils are placed over the cylinder.
  • Gap between each section of H.V. Coils including top & bottom clearances is maintained with the help of oil ducts, as per the design/drawings.
  • The Top Yoke is refilled. Top core frame including core bolts and tie rods are fixed in position.
  • Primary and secondary windings are connected as per the requirements. Phase barrier between H.V. phases are placed as per requirement.
  • Connections to the tapping switch (if required) are made.
  • Finally, the component is placed in the oven.

Tank-Up

The core-coil assembly and tank supplied by the fabrication deptt. are taken into tank-up stage. The procedure is :
  • The core-coil assembly is taken out of the oven and the "Megger test" is carried out.
  • Only if the megger value is as per the specification, the assembly may be taken for tank-up.
  • The tanks, supplied by fabrication deptt. are brought to tank-up department duly painted.
  • Fittings like drain valves, HV& LV Bushings, conservator, oil level indicator and explosion vent are fitted in the tanks.
  • The Core-coil assembly is then placed into the tank and properly locked up.
  • Pure filtered transformer oil is filled in the tank to immerse the assembly only.
  • Connections of primary and secondary to the terminal bushings are made. Operating handle for ratio switch is fitted, wherever required.
We, at Oswal Transformers have a state-of-art in-house facility for manufacturing transformer tanks. All tanks are made of high quality steel and can with stand vaccum as specified by the international standards and the customer. All welds are tested, ensuring 100% leakproof of seems and mechanical strength. Trasnformera with Corrogated Fin-Type radiators can aslo be supplied. The fins are manufactured of Gold-rolled steel.The fin height and length are according to customer's specifications and fins can be plain or embossed. All transformer tanks are given a smooth finishing by using the "SHOT BLASTING" process.

Paint Process

Painting : The entire procedure of painting is done under two stages:

Cleaning of tanks
  • The cleaning of tank is done normally by chipping/grinding.
  • The outside surface of the tank is short blasted to achieve a very fine and smooth finish
Painting of tanks
  • After cleaning the tanks, a coat of hot oil resistence paint is applied on the internal surface of the tank.
  • The outside surface is painted with a coat of Red Oxide primer and subsequently with one coat of enamel paint as per customer's requirement.

Finishing

  • Fittings and accessories as per customer's specification and drawing are checked.
  • Air Pressure test is subjected to avoid any leakage and seepage on all transformer.
  • Transformers are filled with oil upto the minimum level marking, wherever necessary.
  • Loose accessories like, earthing terminals, bimetallic connectors, dial type thermometers are also checked for proper fittings.